filename: tfs 678.doc version 1.5 07.01.2014 vectron international filter specification tfs 678 1/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. measurement condition ambient temperature: 23 c input power level: 0 dbm terminating impedance: input: 50 output: 50 characteristics remark: the maximum attenuation in the pass band is defined as the insertion loss a e . the nominal frequency f n is fixed at 678 mhz without any tolerance or limit . the values of absolute attenuation a abs are guaranteed for the whole operating temperature range. the frequency shift of the filter in the op erating temperature range is included in the production tol erance scheme. d a t a typ. value tolerance / limit insertion loss a e 1,7 db max. 3,0 db nominal frequency f n - 678,0 mhz passband pb - f n 12,0 mhz bandwidth bw 1 db 42,0 db min. 24,0 mhz absolute attenuation a abs 0,3 mhz ... 603 mhz 56 db min. 40 db 603 mhz ... 640 mhz 20 db min. 10 db 711 mhz ... 753 mhz 18 db min. 10 db 753 mhz ... 778 mhz 40 db min. 30 db 778 mhz ... 1008 mhz 48 db min. 40 db 1008 mhz ... 1140 mhz 57 db min. 50 db ip3 min. +30 dbm input power level - max. 0 dbm operating temperature range otr - - 45 c ... + 85 c storage temperature range - - 45 c ... + 85 c temperature coefficient of frequency tc f * -76 ppm/k - *) ? f(hz) =tc f (ppm/k) x(t-t 0 ) x f to (mhz) generated: checked / approved:
filename: tfs 678.doc version 1.5 07.01.2014 vectron international filter specification tfs 678 2/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. filter characteristic construction and pin connection (all dimensions in mm) date code sq 3,81 +0,2/-0,1 1 3 7 5 1,2 max. 0,6 1,78 0,1 1,78 2,54 1 2 0 % % d 1 3 5 7 50 test circuit l1 saw l2 2 6 1, 3, 4, 5, 7, 8 678 e02 1 ground 2 input 3 ground 4 ground 5 ground 6 output 7 ground 8 ground date code: year + week e 2014 f 2015 g 2016 ... 0 200 400 600 800 1000 1200 1400 1600 1800 -100 -90 -80 -70 -60 -50 -40 -30 -20 -10 0 frequency in mhz magnitude in db 650 660 670 680 690 700 -5 -4.5 -4 -3.5 -3 -2.5 -2 -1.5 -1 -0.5 0 frequency in mhz magnitude in db
filename: tfs 678.doc version 1.5 07.01.2014 vectron international filter specification tfs 678 3/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. stability characteristics, reliability after the following tests the filter shall meet the whole specification: 1. shock: 500g, 1 ms, half sine wave, 3 shocks each plane; din iec 68 t2 - 27 2. vibration: 10 hz to 500 hz, 0.35 mm or 5 g respe ctively, 1 octave per min, 10 cycles per plane, 3 planes; din iec 68 t2 - 6 3. change of temperature: -55 c to 125c / 15 min. each / 1 00 cycles din iec 68 part 2 ? 14 test n 4. resistance to solder heat (reflow): reflow possible: three ti mes max.; for temperature conditions refer to the attached " air reflow temperature conditions" on page 4; this filter is rohs compliant (2011/65/eu) packing tape & reel: iec 286 ? 3, with exception of value f or n and minimum bending radius; tape type ii, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: 3000 reel of empty components at start: min. 300 mm reel of empty components at start including leader : min. 500 mm trailer: min. 300 mm g do w ct f e g d1 p2 p1 po bo ao pull off direction pin marker typ date code ko t a c n w 1 w 2 the minimum bending radius is 45 mm. tape (all dimensions in mm) w : 12,00 0,3 po : 4,00 0,1 do : 1,50 +0,1/-0 e : 1,75 0,1 f : 5,50 0,05 g(min) : 0,75 p2 : 2,00 0,05 p1 : 8,00 0,1 d1(min) : 1,50 ao : 4,30 0,1 bo : 4,30 0,1 ct : 9,5 0,1 reel (all dimensions in mm) a : 330 w1 : 12,4 +2/-0 w2(max) : 18,4 n(min) : 50 c : 13,0 +0,5/-0,2
filename: tfs 678.doc version 1.5 07.01.2014 vectron international filter specification tfs 678 4/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. air reflow temperature conditions conditions exposure average ramp-up rate (30c to 217c) less than 3c/ second > 100c between 300 and 600 seconds > 150c between 240 and 500 seconds > 217c between 30 and 150 seconds peak temperature max. 260c time within 5c of actual peak temperature between 10 and 30 seconds cool-down rate (peak to 50c) less than 6c/second time from 30c to peak temperature no greater than 300 seconds temperature / c time / s max. 260c 217c 10 ... 30 s 30 ... 150 s max. 300 s chip-mount air reflow profile
filename: tfs 678.doc version 1.5 07.01.2014 vectron international filter specification tfs 678 5/5 vectron international gmbh potsdamer stra?e 18 d 14 513 teltow / germany tel: (+49) 3328 4784-0 / fax: (+49) 3328 4784-30 e-mail: tft@vectron.com vectron international gmbh reserves the right to ma ke changes to the product(s) and/or information con tained herein without notice. no liability is assumed as a result of their use or application. no rights under any patent accompany the sale of any such product(s) or information. history version reason of changes name date 1.0 generation of development specification strehl 15.01.2007 1.1 changing data section according to customer req uirement martens 28.03.2007 1.2 change absolute attenuation strehl 04.04.2007 1.3 change attenuation s. channaa 04.03.2008 1.4 change attenuation, add typical values add filter characteristic, generation of filter sp ecification s. channaa 09.05.2008 1.5 maximum input power updated korte nbeutel 07.01.2014
|
